About
Description
Link ECU Subaru WRXLink V11 - WRX11X Plug in
*NOTE* This product is Order in and typically takes around a 4-5 working days to get in to stock
G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car.
This ECU fits inside the factory OEM enclosure. Installation of processing unit is a breeze, with no alteration of the factory wiring loom required for the models listed below.
Due to the amount of variation on this vehicle, please ensure you read the Configuration - Memo Text in PCLink.
This product supports the following models:
- 2007-2014 WRX and WRX STI with GR/GV/GH/GE chassis codes, for JDM/AUDM/SADM/EURO markets, with turbocharged EJ20 or EJ25 engines.
- 2008-2010 USDM models which have the common international Denso ECU Pinout**
- 2015-2021 WRX STI with VAB/VAF chassis codes, for JDM/AUDM/SADM/EURO markets, with turbocharged EJ20 or EJ25 engines
**Note: Refer to the supported models document below for more detail. 2011 and later USDM models are supported by our WRX11 USDM ECU
Take a look at our supported models list to find out which models are supported and which are not. Alternatively, contact your LinkECU Reseller or our 24/6 Tech Support Team.
Important Notes
- Please check your connector matches the header in the listed photo before purchasing.
- This ECU works for manual transmissions only.
- Air temp sensor highly recommended.
- Most factory features are supported including DCCD, hill start assist, SI drive, cruise control, cam control & ABS supported.
- Check the features tab for I/O input & output expansion options.
- The security/immobiliser lamp may remain illuminated in some models
Note: This Plug-in features a new 4 pin powered CAN connector and cannot use the old CANPCB cable for CAN connection. Use the CANJST4 (Link PN 101-0198) cable for connecting CAN devices. This new 4 pin port and cable provide not only the CAN connection, but also a protected 12V power supply and ground for powering the CAN devices. The power supply is protected by a self-resetting fuse rated at 3A continuous.
G4X PlugIn Key Features (where applicable):
Up to 6D fuel and ignition mapping
Precision closed loop cam control (four cam, independent control)
Sequential fuel delivery
Digital triggering, all OEM patterns
OEM idle hardware supported
5D boost control with three switchable tables
Motorsport features - antilag, launch, flat shift
Continuous barometric correction (on board)
CAN port
QuickTune - automated fuel tuning
Individual cylinder correction
USB tuning cable included
Stats recording into on-board memory
Gear compensations for spark, boost and fuel
Real time selectable dual fuel, ignition and boost maps
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
Boost control referenced to gear, speed or throttle position
512 mega bytes data logging memory within storage unit
Staged injection
Knock with "windowing"
I/O Options:
The following expansion connector inputs/outputs are provided:
Expansion connector 1
Pin 1 Aux 16
Pin 2 DI 11
Pin 3 An Temp 4
Pin 4 Knock 2
Pin 5 Injector 6
Description
Link ECU Subaru WRXLink V11 - WRX11X Plug in
*NOTE* This product is Order in and typically takes around a 4-5 working days to get in to stock
G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car.
This ECU fits inside the factory OEM enclosure. Installation of processing unit is a breeze, with no alteration of the factory wiring loom required for the models listed below.
Due to the amount of variation on this vehicle, please ensure you read the Configuration - Memo Text in PCLink.
This product supports the following models:
- 2007-2014 WRX and WRX STI with GR/GV/GH/GE chassis codes, for JDM/AUDM/SADM/EURO markets, with turbocharged EJ20 or EJ25 engines.
- 2008-2010 USDM models which have the common international Denso ECU Pinout**
- 2015-2021 WRX STI with VAB/VAF chassis codes, for JDM/AUDM/SADM/EURO markets, with turbocharged EJ20 or EJ25 engines
**Note: Refer to the supported models document below for more detail. 2011 and later USDM models are supported by our WRX11 USDM ECU
Take a look at our supported models list to find out which models are supported and which are not. Alternatively, contact your LinkECU Reseller or our 24/6 Tech Support Team.
Important Notes
- Please check your connector matches the header in the listed photo before purchasing.
- This ECU works for manual transmissions only.
- Air temp sensor highly recommended.
- Most factory features are supported including DCCD, hill start assist, SI drive, cruise control, cam control & ABS supported.
- Check the features tab for I/O input & output expansion options.
- The security/immobiliser lamp may remain illuminated in some models
Note: This Plug-in features a new 4 pin powered CAN connector and cannot use the old CANPCB cable for CAN connection. Use the CANJST4 (Link PN 101-0198) cable for connecting CAN devices. This new 4 pin port and cable provide not only the CAN connection, but also a protected 12V power supply and ground for powering the CAN devices. The power supply is protected by a self-resetting fuse rated at 3A continuous.
G4X PlugIn Key Features (where applicable):
Up to 6D fuel and ignition mapping
Precision closed loop cam control (four cam, independent control)
Sequential fuel delivery
Digital triggering, all OEM patterns
OEM idle hardware supported
5D boost control with three switchable tables
Motorsport features - antilag, launch, flat shift
Continuous barometric correction (on board)
CAN port
QuickTune - automated fuel tuning
Individual cylinder correction
USB tuning cable included
Stats recording into on-board memory
Gear compensations for spark, boost and fuel
Real time selectable dual fuel, ignition and boost maps
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
Boost control referenced to gear, speed or throttle position
512 mega bytes data logging memory within storage unit
Staged injection
Knock with "windowing"
I/O Options:
The following expansion connector inputs/outputs are provided:
Expansion connector 1
Pin 1 Aux 16
Pin 2 DI 11
Pin 3 An Temp 4
Pin 4 Knock 2
Pin 5 Injector 6
Link ECU Subaru WRXLink V11 - WRX11X Plug in (Order in)
- Regular price
- $2,984.24
- Sale price
- $2,984.24
- Regular price
-
Tax included.
Shipping calculated at checkout.
Translation missing: en.products.product.sku:SCR LNKWRX11X
Couldn't load pickup availability
Order in
NZ’s Fastest Auto Parts Shippers
Scarles Shipping
We ship throughout New Zealand using NZ Post, NZ Couriers, and Owens Freight, depending on the size and weight of your order.
Shipping rates are calculated at checkout based on your location and the items in your cart.
Delivery timeframes:
Auckland: overnight
Rest of North Island: 1–2 days
South Island: 1–3 days
Bulky and freight items
Some items, including race seats, large exhaust systems, and oversized freight, are shipped via our freight carrier. Rates for these are shown at checkout. For rural South Island delivery on large items, we'll contact you with a quote before dispatch.
International orders
We don't offer automatic international shipping rates. Request a quote, and we'll get back to you with rates and delivery times before you purchase.
Questions?
Head to our FAQs or contact us - we're here to help.
We provide hassle-free shopping with super fast shipping for all your parts needs.
Open 7 Days
Refunds and Returns Policy
We accept returns within 14 days after the invoice date, if the product isn't suitable for your application. The product must be returned in original condition (how we sold or sent it to you) and with our packaging. Full Refunds/Store Credit are not issued in this instance, however we can exchange it with another product. If an exchange product is not required, a refund may be issued subject to a 15% restocking fee (freight costs cannot be returned). Any product returned damaged or not in saleable condition will be assessed and an appropriate damage fee will apply. This policy excludes drop-shipped, clearance, sale items or special order products.
Email sales@scarles.co.nz for refund or return information.
FAULTY PRODUCT
Any issue or fault with a product must be brought to our attention immediately by contacting us at sales@scarles.co.nz before any action is taken. We will then consider the best course of action, which may include you returning the product for inspection.
Once the item is received we will assess the fault. All faulty products will be inspected/tested by either the original manufacturer or a professional. This process time frame varies depending on the product. If the product is deemed a manufacture fault a full refund or replacement can be offered.
We do not cover any additional fitment costs, certification costs, extra parts or freight required to make the item fit or work or any loss of time/wages/business occurred. The product provided even if it is stated as a “direct fit” does not imply no additional parts maybe required.
TRADEME
Please note: Items sold on Trade Me are offered on an ‘as is, where is’ basis. As the factory warranty is no longer valid, we’re unable to provide additional cover on these products.
For more information head over to our FAQs page or email us sales@scarles.co.nz
Got questions? Visit our store or contact us for any product or order-related queries.
